Title:
Experimental Design in Constructing Low Temperature Sensor Based on Resistance Temperature Detector (RTD)
Author:
Suwito Singgih(1*)
Moh Toifur(2)
Suryandari Suryandari(3) (1) Tidar University, Indonesia
(2) Ahmad Dahlan University, Indonesia
(3) UIN Antasari Banjarmasin, Indonesia
(*) Corresponding Author
10.31002/ijose.v4i2.2758|
Abstract views : 31
|
PDF views : 0
Abstract
Thin film copper-based RTD still has a low TCR. Hence, plating a Cu-based RTD with nickel will develop a higher TCR. TCR is the sensitivity of RTD’s value in response to temperature change. The experimental design in constructing Cu/Ni thin film by using the electroplating method with a concentration of solution and electrode spacing’s variation has been done. Electroplating is performed with a concentration of solution and electrode spacing’s variations. Electroplating processed by limiting DC voltage to 6 volts. Electrolyte solutions composition were NiSO4, Ni2Cl2, H3BO3 and aquades. Concentrations of solutions can be varied by changing NiSO4 and Ni2Cl2 masses. Based on these concentrations of solutes and electrode’s spacing, this research used 15 samples. Thickness, thin-film resistance, and temperature sensor test are performed to each sample. The purpose of thickness test is to measure nickel plates which were formed from the electroplating process. Thin-film resistance test performed to measure sample resistance changing to the electroplating process, and the temperature sensor test was performed to measures the sample’s sensitivity in responding to temperature changes. This research’s result shows the greater the concentrations of solutes used for copper electroplating, the thicker nickel plates will form. This condition makes its resistance’s value decreasing.
Keywords: thin layer resistance, concentration of the solution, electrode distance, electroplating, thin layers of Cu / Ni, RTD, modules
Full Text:
PDFReferences
Adnyani, Ida Ayu Sri dan A A Alit Triadi. 2009. Pengaruh Kuat Dan Distribusi rus Terhadap Ketebalan Dan Kekerasan Lapisan Krom Pada Stoneware dan Earthenware. Jurnal. Jurnal Teknologi Elektro Vol. 8 No.2 Juli - Desember 2009.
Afriany, Reny., Kusmono dan R. Soekrisno. 2012. Pengaruh Konsentrasi Larutan Dan Waktu Pelapisan Nikel Pada Alumunium Terhadap Kekerasan. Jurnal. Prosiding Seminar Nasional Aplikasi Sains & Teknologi (SNAST) Periode III. Yogyakarta, 3 November 2012. ISSN: 1979-911X.
Basmal, Bayuseno dan Sri Nugroho. 2012. Pengaruh Suhu dan Waktu Pelapisan Tembaga-Nikel pada Baja Karbon Rendah Secara Elektroplating Terhadap Nilai Ketebalan dan Kekasaran. Jurnal. ROTASI Vol.. 14, No. 2, April 2012 (23-28)
Bevington, R.R dan D.K. Robinson.1992. Data Reduction and Error Analysis for The Physical Sciences. Singapore: McGraw-Hill Book.
Chosim S Widodo dan Jasmadi. 2008. Panduan Menyusun Bahan Ajar Berbasis Kompetensi. Jakarta: PT Alex Media Komputindo.
Chowdhury, Tasnuva dan Haider Bulbul. 2010. Design of a temperature sensitive voltage Regulator for AC Load Using RTD. Jurnal. International Journal of Engineering Science and Technology. Vol. 2 No. 12, p.7896-7903.
Depdiknas. 2008. Pengembangan Bahan Ajar. Sosialisasi KTSP 2008. Jakarta: Depdiknas
Fraden, Jacob. 2004. Handbook of Modern Sensor : Phisics, Designs and Applications.San Diego: Advanced Monitors Cooperation
Fraden, Jacob. 2010. Handbook of Modern Sensor. San Diego: Advanced Monitors Cooperation
Gunawan, Budi dan Citra D. Azhari. Karakterisasi Spektofotometri IR dan Scanning Electron Microscopy (SEM) Sensor Gas dari Bahan Polimer Poly Ethelyn Glycol (PEG). Jurnal. ISSN 1979-6870
Halliday, Resnick. 1993. Fundamentals of Physics.
Haryadi, Moh. Toifur dan Bagus. 2014. Cow Cement Sensor Based On Coil Resistance Temperature Detector (C-RTD) Coupled With Four Wire Configuration Bridge (4-WCB). Jurnal. 7th International Conference on Physics and Its Applications 2014 (ICOPIA 2014)
Haskia. 2007. Perkembangan Teknologi Sensor dan Aplikasinya untuk Diteksi Radiasi Nuklir. Jurnal. Prosiding PPI - PDIPTN 2007 Pustek Akselerator dan Proses Bahan - BATAN. ISSN: 0216 – 3128. p.9-20
Imran, Muhammad dan Abhijit Bhattacharyya. 2006. Effect of Thin Film Thicknesses and Materials on theResponse of RTDs Ana Microthermocouples. Jurnal. IEEE Sensors Journal, Vol. 6, No. 6, December 2006.
Indratno, Toni Kus dan Moh. Toifur. 2015. Optimasi Diameter Dan Panjang Kawat Koil Sebagai Kandidat Sensor Suhu Semen Sapi Berbasis RTD-C. Jurnal. OMEGA Jurnal Fisika dan Pendidikan Fisika Vol 1, No 2. p. 45-49
Kurneli, Osye, Ahmad A. Sonief, E. Sulistyo. Pengaruh Variasi Jarak antara Anoda dan Katoda Hard Chrome Terhadap Kekerasan pada Baja AISI 1025 Hasil Perlakuan Panas Tempering. Jurnal. Fakultas Teknik. Universitas Brawijaya.
Maher, Anthony., Vijayalakshmi Velusamy, Daniel Riordan and Joseph Walsh. 2014. Modelling of Temperature Coefficient of Resistance of a Thin Film RTD Towards Exhaust Gas Measurement Applications. Jurnal. Proceedings of the 8th International Conference on Sensing Technology, p.19-22
Nusse, D. , Noetzel, R. and Vdi, 2008. Temperature Sensors in Nickel Thin Film Technology. Jurnal. in Sensoren Und Messsysteme 2008. 2008. p. 891898.
O’Grady, A. 2000. Transducer/Sensor Excitation and Measurement Technique, Analog Dialogue. (34/5)
Rasyad, Abdul dan Budiarto. 2011. Pengaruh Waktu Elektroplating dan Powdercoating NiCr Terhadap Sifat Mekanis dan Struktur Mikro pada Baja Karbon SPCC-SD. Jurnal. Prosiding Seminar Nasional Pengembangan Nuklir IV. Pusat Pengembangan Energi Nuklir. Badan Tenaga Nuklir Nasional.
Riswanto. 2014. Optimasi Panjang Kawat dan Diameter Kawat Tembaga Sebagai Piranti Sensor Suhu Rendah Berbasis 4 WCB RTD. Tesis, Yogyakarta: UAD.
Safitri, Juwita, dkk. 2014. Rancang Bangun Alat Ukur Resistivitas Pada Lapisan Tipis Menggunakan Metode 4 Probe Berbasis ATMega 8535 Dengan Tampilan LCD Berkarakter 2X16. Jurnal Fisika Unand Vol. 3 No. 2 April 2014.
Sen, T.K. Pan, P. Ghosal and S.K. 2011. An Improved Lead Wire Compensation Technique for Conventional Four Wire Resistance Temperature Detectors (RTDs). Jurnal. Departemen of Applied Physics, Vniversity of Calcutta, India.
Serway, Raymond A., dan John W. Jewett. 2004. Physics for Scientist and Engineers.Thomson Brooks.
Soekardjo & L. Permana. 2009. Metodologi Penelitian Pendidikan Kimia. Diktat Kuliah.Yogyakarta: UNY Press
Sudjatmoko. 2005. Kajian Sifat Bahan Lapisan Tipis Feromagnetik NixFe1-X Hasil Deposisi dengan Teknik Evaporasi Hampa. Jurnal. Prosiding PPI-PDIPTN 2005. ISSN 0216–3128. p.111-117.
Sugiyarta, A.P. Bayuseno, Sri Nugroho. 2012. Pengaruh Konsentrasi Larutan dan Kuat Arus Terhadap Ketebalan pada Proses Pelapisan Nikel Untuk Baja Karbon Rendah. Jurnal. ROTASI- Vol. 14. No. 4, Oktober 2012 (23-27).
Sukarelawan, M.Irma 2015. Rancang Bangun Eksperimen Sensor Suhu Rendah Cu/Ni Berbasis Film Tipis RTD (Resistance Temperature Detector) dengan Metode Elektroplating Menggunakan Rangkaian 4-WCB (Four Wire Configuration Bridge). Tesis. Universitas Ahmad Dahlan.
Suryanarayana, C dan M.G. Norton. 1998. X-ray Diffraction, A Practical Approach.
Sutomo, Senen, Rahmat. Pengaruh Arus dan Waktu pada Pelapisan Nikel dengan Elektroplating untuk Bentuk Plat. Jurnal. Fakultas Teknik. Universitas Diponegoro.
Toifur, Moh. 2007. Deposition of Cu/Ag At The Various Deposition Time For Resulting The High Quality Decorative Silver, Proceeding of The International. Jurnal. Seminar on Natural Sciences and Applied Natural Sciences, Yogyakarta 2007, ISBN: 978-979-3812-09-0
Wilson, Jon S. 2005. Sensor Technology Handbook.Newnes.
DOI: http://dx.doi.org/10.31002/ijose.v4i2.2758
Article Metrics
Abstract view : 31 timesPDF - 0 times
Cited By
Refbacks
- There are currently no refbacks.
Copyright (c) 2020
